Laser Performance Pico/Funboat Upper Mast Base Plug black plastic fits on the bottom of the top mast fixed with 2 x rivets (sold separately). Specifications Material: Plastic Colour: Black

ILCA Laser Boom with Harken ball bearing blocks. Official ILCA approved for all ILCA events and suitlable for all Rigs- ILCA 4, ILCA 6, ILCA 7. Features Harken Boom End and  Centre MainsheetsBlocks fitted Official ILCA approved Suits All modesl...

Plug black plastic fits on the top of the top mast fixed with rivets x 2 (sold seperately).Can also be used as Laser Pico Top Mast Plug. Specifications Material: Plastic Colour: Black

The Laser Boom Fairlead in blue plastic to tie the clew hook to the boom. Also used for traveller or boom outhaul. Features Fitting requires rivets 3/16" x 3/4" (sold seperately) Also used for clew outhaul fairlead on laser...

This large blue plastic Laser Boom Fairlead has a stainless steel insert to reduce chafing and allow larger lines with heavier loads. Features Suits the topaz deck fairlead Requires 2 x screw (6 mm x 25 mm) Specifications Material:...

The Clamcleat® CL211 Mk1 Racing Junior is a very strong allow cleat with a fairlead to guide the rope into the teeth. The specially shaped base means the CL211 Mk1  means it can be fitted to either curved or flat surfaces The CL211 Mk1AN...

Anodized aluminium tube with end plugs and sleeve fitted. A direct replacement for the top mast that comes on your Laser 4.7, Radial or Standard rig. Suits all types of Laser sailing boat. The Laser Top Mast is too long for a regular courier so there is...

The ILCA Laser rudder retaining clip prevents the rudder popping up and becoming detached. The rudder clip is easy to fit but remember to use Sikaflex or similiar sealant to keep the hull watertight.

The Pico Toe Strap plate is used to spread the load when attaching toe strap or MK1/MK2 Laser friction pad. Specification Material: Plastic Colour: Blue

Laser Toe Strap Padded in grey with XD logo. Internal plastic stiffener stops the Laser Toe Strap from turning over, heat sealed screw holes for easy fit.

The ILCA  Laser Grab Rail Grommets are for attaching the Laser Grab Rail. The Grab Rail requires five per side. Grommets are supplied in a pack of ten which will complete one ILCA Laser Hull. Remember to put Sikaflex on before you attached the Grab...

Holt Laser Grab Rail fit all Laser Performance and ILCA Dinghies  - Two required per boat - It is recommended to use a sealant, such as Sikaflex 291i to bed screws  Accessories Sikaflex 291i Sealant - Click here  

Official ILCA approved Nautos self-bailer ( Autobailer)  - Suits all models ILCA and Laser

Standard Bow eye fairlead for all Laser and ILCA rig sail boats

The Laser XD deck fairlead with 23 mm holes. Specifications Width: 23 mm

Aluminium deck cleat is designed to hold 12mm to 16mm rope under high pressure. Specification Material: Aluminium Rope diameter: 1/2 - 5/8" (12 mm - 16 mm) Hole diameter: 3 3/4" (95 mm) Length: 4 5/8" (118 mm) Width: 1 1/2" (37 mm) Height: 1 3/4"...

The Laser Harken Cammetrick cleat is similar to the Laser Cleat 91517 but this one comes made in plastic. Harken Micro Cam Cleats hold lines securely and release instantly for easy, precise trimming. Lightweight fiber-reinforced Carbo-Cams for racing...

ILCA Laser Centreboard or Daggerboard Stops - These push-together sets prevent the Daggerboard dropping too low  How to assemble Allign the first cap fitting to the centre shaft and push down hard to until the shaft is flush with outer side of...

The ILCA Laser Friction Pad MK2 is screwed to the back of your daggerboard casing and allows for perfect grip and slip ratio when raising the board.

The MK1 flat back rubber friction pad for the deck of any Laser dinghy designed as a friction plate to keep the Laser daggerboard in place during sailing.

Laser Rudders Gudgeons by Holt - 2 Required per boat  Fasteners 2 x Sowester Pan Head Self Tappers per Gudgeon - Size  8 x 1 1/2"  Select size here

Genuine ILCA Rudder Gudgeon asteners 4 x Sowester Pan Head Self Tappers per Gudgeon - Size  8 x 1 1/2"  Select size here

This ILCA / Laser tiller retaining pin secures the tiller to the rudder head. Note If your tiller is not drilled to receive the retaining pin, ensure the tiller is firmlypressed into the head before drilling the location hole to ensure solid fit

Official ILCA Rudder Head comes with rudder megabolt.  Suits all models ILCA 4, 6 & 7 and Laser 4.7, Radial and Full Rig

The Laser rudder head is a aluminium construction complete with a rudder ring and tilller retaining pin. Rudder fittings are stainless steal for long lasting, please make sure you rudder head has the approve sticker for eventing. Comes with rudder...

High quality carbon tiller extension from Holt 23mm dia. x 120cm, including flexible tiller joint ideal for ILCA all rig Features ILCA and Laser approved Carbon fibre  Comes with tiller joint

The Rooster Carbon Tiller Extension 1250mm is available in a number of different section diameters: 19mm diameter - Rooster added this size to their range to give more room in your hand to hold the sheet. 22mm diameter - The most popular and...

Aluminium tiller extension complete with UJ and rubber non slip covering. Specifications Material: Aluminium Length: 1067 mm

Older style articulated stainless steel tiller joint for smaller sailing dinghies

High quality, reliable RWO OmniflexTiller Joint to suit most dinghy tiller extension, including ILCA Laser, Topper, and many others. This Omniflex joint is made from Elastomeric polymer which allows all directional flexability. The fitting includes a...

The very popular Sowester Laser Gorilla Tiller & Extension is made to last and ideal for training, schools and club sailing - It suits all rigs of Laser class sailing dinghies and includes RWO 107cm tiller extension with flexible joint.

The Rooster Carbon Laser Tiller - Plate Version is arguably the strongest tiller on the market utilizing space age technology.Manufactured on a mandrill with pre-preg materials to produce the most consolidated carbon fibers ever! Each tiller is...

The Laser Tiller Extension made from carbon fibre it comes with a flexible tiller joint that attaches to your main tiller. Designed for the Laser XD range of racing hardware for the any class of Laser. Specifications Material: Carbon Diameter:...

The ILCA Mega Bolt is the pivot bolt to fit the Rudder Head to the Rudders Plade - Supplied with 20mm Washers 

The Laser XD rudder head pivot bolt is an upgraded large diameter bolt and nylock nut with 20 mm washers. The rudder bolt will hold your rudder blade firmly in place.

Official ILCA fused rudder blade only - Suits all Rigs and Class legal for all ILCA events. Note Also suits Laser (Torch logo) Sailboats.

Laser shock cord retainer with plastic clip keeps dagger board in place. Specifications Colour: Black Length: 7 mm

Laser Performance Daggerboard Infused.

The Laser Lower Vang Block is used for the Laser Pico and Laser Standard rig sailboats on the top section of the Vang which attaches to the eye plate on the boom.Comes with removable pin to attach to eye plate (eye plate LS-91532 sold...

This Harken T2 Double Block is used as a replacement for the Laser Vang but can used with many different applications for dinghy sailing. The Harken 18 mm T2 Block is used in dinghy applications including the direct replacement for the Laser Vang Double...