International Toplac Plus Topcoat - Mediterranean White - 2.5L

International Toplac Plus is a silicone alkyd premium gloss yacht enamel for all substrates above the waterline. It is easy to apply by roller without the need for tipping. Toplac Plus contains UV filters for increased durability.

Features

• Improved aesthetics over Toplac in terms of Distinction Of Image (DOI) and flow
• The new formula eliminates the need for tipping when using a roller
• Use One UP followed by Toplac Plus to deliver the best in class topcoat system offered by International

Specifications

• Brand: International
• Capacity: 2.5L
• Area: Above & Below the Waterline
• Suitable for: Hull
• Finish/Sheen: High Gloss
• Substrates: Aluminium/Zinc-Galvanised Steel, Epoxy Composite/Carbon Fibre, Cast Iron, GRP/FRP, Lead, Steel, Wood, Bronze/Stainless Steel
• Application Method: Brush, Roller
• Recommended Number of Coats: 2 - 3
• Practical Coverage: 12 m²/L
• Typical Shelf Life: 2 Years

Colour Avaliablity

• Mediterranean White

Preparation

PREVIOUSLY PAINTED SURFACE

• In Good Condition: Wash down with a suitable detergent, rinse with fresh water and allow to dry. Abrade with 280-320 grade (grit) paper.
• In Poor Condition: Remove all previous coatings and prime the substrate.

PRIMING: Substrate preparation is covered separately on the primer datasheet. (One UP).

BARE WOOD: Sand smooth with 80­-180 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent, allow to dry completely before applying recommended products.

STEEL: Degrease with solvent or Super Cleaner. Gritblast to Sa 2½ ­ near white metal surface. If gritblasting is not possible, grind the metal surface with 24­36 grit abrasive discs to a uniform, clean, bright well roughened metal surface. 50­-75­microns anchor pattern. Use angle grinder on small areas. Clean thoroughly and allow to dry.

ALUMINIUM: Degrease with solvent or Super Cleaner. Sand well using 60-­120 grade (aluminium compatible) paper.
Clean thoroughly and allow to dry. Prime with One UP as soon as possible (within 8 hours).

GRP: Degrease with solvent or Super Cleaner. Sand well using 180­-220 grade paper. Clean thoroughly and allow to dry.

AGED/WEATHERED GELCOATS: Due to increased porousness, the risk of solvent/moisture entrapment is increased, leading to potential blistering. To reduce this risk 3 coats of Interprotect are recommended to seal the gelcoat. Interprotect must be overcoated with One UP prior to topcoat application.

ALL SUBSTRATES: Prime with suitable primer.

Method

Sand the undercoat smooth with 320-­400 grade (grit) wet or dry paper. Remove dust with a dust wipe. Apply 2-­3 coats of Toplac Plus.

Hints

• Mixing: Stir well before use
• Thinner: Thinner No 100. Brush/Roller
• Thinning: Add 10% Thinner No 100 to ease the application by brush/roller. The thinner quantity can be adjusted with climate conditions. At temperature above 25C an extra 5% thinner No 100 should be added.
• Cleaner: Thinner No 1 or Thinner No 100.
• Ventilation and Humidity Control: Apply in dry, well ventilated conditions.: Add 10% Thinner No 100 to ease the application by brush/roller. The thinner quantity can be adjusted with climate conditions. At temperature above 25C an extra 5% thinner No 100 should be added.
• Cleaner: Thinner No 1 or Thinner No 100.
• Ventilation and Humidity Control: Apply in dry, well ventilated conditions.

Hazard Warnings

Hazard Pictogram :
Signal Word:	Warning
Hazard Statements:	Flammable liquid and vapour May cause drowsiness or dizziness Harmful to aquatic life with long lasting effects
Precautionary Statement:	General: Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. Prevention: Wear protective gloves. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use only outdoors or in a well-ventilated area. Avoid release to the environment. Response: IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. Storage: Keep cool. Disposal: Dispose of contents and container in accordance with all local, regional, national and international regulations.
Hazardous Ingredients	Hydrocarbons, C9-C11, N-Alkanes, Isoalkanes, Cyclics.
Supplemental Label Elements	Warning! Hazardous respirable droplets may be formed when sprayed. Do not breathe spray or mist.

Technical Files

Technical Data Sheet

Safety Data Sheet