International Interdeck Non-Skid Deck Paint - 750ml

International Interdeck Non-Skid Deck Paint is tough, slip resistant deck paint that protects the surface from every day wear and tear. It’s easy to apply, comes in a range of colours and its low sheen finish helps prevent sunlight from reflecting off decks.

Features

• Slip-resistant deck paint that’s suitable for all substrates
• Contains fine mineral additive for hard wearing, non-slip surface
• Low sheen finish prevents sunlight dazzle

Specification

• Brand: International
• Capacity: 750ml
• Area: Above the Waterline
• Suitable for: Deck-non-skid
• Substrates: Aluminium/Zinc-Galvanised Steel, GRP/FRP, Steel, Wood
• Finish/Sheen: Matt
• Application Method: Brush, Roller
• Recommended Number of Coats: 1 - 2
• Practical Coverage: 10.08 m²/L
• Typical Shelf Life: 2 Years

Colour Avaliablity

• White
• Squall Blue
• Cream
• Grey
• Sand Beige

Preparation

PREVIOUSLY PAINTED SURFACES

• In Good Condition - Wash down with International Super Cleaner, rinse with fresh water and allow to dry. Abrade with 280-­320 grade paper. 
• In Poor Condition - Remove all previous coatings and prime the substrate with the appropiate primer

PRIMING All preparation for bare substrates is covered on the appropriate primer datasheet.

BARE WOOD Sand smooth with 80­180 grade paper and then 280 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying products recommended for application direct to wood (see specific coating systems).

STEEL Degrease with solvent or suitable detergent cleaner. Gritblast to Sa 2½ ­ near white metal surface. If gritblasting is not possible, grind the metal surface with 24­36 grit abrasive discs to a uniform, clean, bright metal surface with a 50­-75 microns anchor pattern. Use angle grinder on small areas. Clean thoroughly and allow to dry. Pre­prime using an International primer as detailed for specific coating systems.

ALUMINIUM Degrease with solvent or suitable detergent cleaner. Sand well using 24­120 grade (aluminium compatible) paper. Coarser grades are recommended to achieve optimum adhesion. Clean thoroughly and allow to dry. Pre­prime using an International primer as soon as possible (within 8 hours) as detailed for specific coating systems.

GRP Degrease with solvent or suitable detergent cleaner. Sand well using 60­120 grade paper. Clean thoroughly and allow to dry. Pre­prime using an International primer as detailed for specific coating systems.

AGED/WEATHERED GELCOATS Due to the potentially porous nature of aged/weathered gelcoats the risk of solvent/moisture entrapment after painting is much higher than when gelcoat is new. As a result this entrapment could lead to blistering of the paint film. To reduce the risk of paint film blistering it is recommended that 3 coats of Interprotect are applied to seal the gelcoat. Interprotect must be overcoated with Perfection Undercoat prior to topcoat application.

ALL SUBSTRATES If any filling is required use the appropriate product from the International range.

Method

Sand the primer with 180­220 grade wet or dry paper. Remove dust with a dust wipe. Apply 1­2 coats.

Hints

• Mixing: Stir well before use.
• Thinner: YTA800 Thinners No.1
• Cleaner: Thinners No.1
• Ventilation and Humidity: Control Apply in dry, well ventilated conditions.
• Other: For best results either stipple by brush or use a mohair roller.

Hazard Warnings

Hazard Pictogram :
Signal Word:	Warning
Hazard Statements:	Flammable liquid and vapour May cause drowsiness or dizziness May cause damage to organs through prolonged or repeated exposure
Precautionary Statement:	General: Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. Prevention: Wear protective gloves. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use only outdoors or in a well-ventilated area. Do not breathe vapour. Response: IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. Storage: Keep cool. Disposal: Dispose of contents and container in accordance with all local, regional, national and international regulations.
Hazardous Ingredients	All Colours : Hydrocarbons, C9-C11, N-alkanes, Isoalkanes, Cyclics, Crystalline Silica, Respirable Powder.

Technical Files

Technical Data Sheet

White - Safety Data Sheet

Cream - Safety Data Sheet

Grey - Safety Data Sheet

Beige - Safety Data Sheet

Squall Blue - Safety Data Sheet