International Compass Varnish - 2.5L

International Compass Varnish is a great quality one-component high gloss varnish suitable for interior & exterior use. It has exceptional durability providing a long lasting rich amber appearance. This product is hard and is extremely resistant to abrasion and chemicals.

Features

• Suitable for all internal and external woods; including oily timbers, such as Teak and Iroko
• Contains HALS and UV absorbers to protect wood from sunlight
• Apply 2 coats per day, sand only after 2-3 coats

Specification

• Brand: International
• Capacity: 2.5L
• Area: Above the Waterline
• Suitable for: Exterior Cabin/Trims, Interior Cabin/Trims
• Finish/Sheen: High Gloss
• Suitable Water Types: Sea Water, Fresh Water, Brackish Water
• Substrates: Wood
• Application Method: Brush, Conventional Spray, Roller
• Recommended Number of Coats: 3 - 5
• Practical Coverage: 12.90 m²/L
• Typical Shelf Life: 2 Years

Preparation

PREVIOUSLY VARNISHED WOOD

• In Good Condition: Clean with thinners. Sand smooth with 280­-320 grade paper. Remove sanding dust with thinners. 
• In Poor Condition: Remove all previous coatings. Apply a minimum of 3­-5 coats. Sand every 2­-3 coats, using 320-­400 grade paper - Remove sanding dust with a dust wipe. 

BARE WOOD Sand smooth with 80­-180 grade paper and then 280 grade paper. Remove sanding dust by brushing, dusting and wiping. If wiping with solvent then allow to dry completely before applying the first coat. 

OILY WOODS e.g. Teak Must be adequately degreased (Thinners No.1 is recommended) and prepared prior to application of Compass. Ensure the surface is completely dry before applying the first coat. Prime, if required, with an International Prime

BRUSH/ROLLER If no primer has been applied, thin the first coat 30% with Thinner No.1. Subsequent coats can be thinned up to 15% dependent upon ambient temperature, application conditions and personal preference. Apply a further 3­5 coats (brush)/ 4­6 coats (roller), until satisfactory finish is achieved. Sand every 2­3 coats, using 320­400 grade paper.* Remove sanding dust with a dust wipe. * Initial aesthetics may be further improved by sanding between every coat.

Method

Pour the amount you expect to use in a separate container. Avoid using direct from the can. Strain it through a paint strainer to ensure there is no contamination. Do not apply too thickly.

Hints

• Mixing: Stir thoroughly before use.
• Thinner: Brush ­ YTA800 Thinner No. 1. Spray ­ Thinner 910 or Thinner 920
• Thinning: Thin the first coat by 30% using recommended thinner. Subsequent coats can be thinned up to 15% dependent upon ambient temperature, application conditions and personal preference to allow best finish.
• Cleaner: Thinners No.1 (YTA800)
• Conventional Spray (Professional spray application only): Pressure Pot: 1­2 bar 14.5­29 psi (gun pressure), 8­10 psi (air pressure) Tip Size: 1.2­1.4 mm. Thin 20­25% with Thinner 910 or Thinner 920.
• Brush: Always use a clean brush that is kept specifically for varnishing. Clean brushes before use.
• Roller: If rolling, use a thin nap roller and "tip­off" with a clean natural bristle brush or pad otherwise air bubbles may become trapped in the film.
• Other: Spray pressures listed are recommendations only. The applicator may use any settings which yield the best results for the individual spraying technique and current weather conditions. Avoid using direct from the can. Pour the amount you expect to use in a separate container. When applying Compass by brush or roller, it may be necessary to adjust the number of coats applied to ensure the total specified system dry film thickness is achieved.

Hazard Warnings

Hazard Pictogram :
Signal Word:	Warning
Hazard Statements:	Flammable liquid and vapour May cause drowsiness or dizziness Toxic to aquatic life with long lasting effects
Precautionary Statement:	General: Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. Prevention: Wear protective gloves. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use only outdoors or in a well-ventilated area. Avoid release to the environment. Response: IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. Storage: Keep cool. Disposal: Dispose of contents and container in accordance with all local, regional, national and international regulations.
Hazardous Ingredients	Hydrocarbons, C9-C11, Isoalkanes, Cyclics, <2% Aromatics.
Supplemental Label Elements	Wear appropriate respirator when ventilation is inadequate.

Technical Files

Technical Data Sheet

Safety Data Sheet