null
Ireland EU online store
Star brite

Starbrite Descaling Motor Flush - 3.78L

SKU:
ST092600
UPC:
071247926026
MPN:
092600
€116.95
Frequently bought together:

Description

Starbrite Descaling Engine Flush is designed to safely and quickly remove scale, calcium deposits, corrosion, salt and carbon buildup in your engine’s cooling and wet exhaust systems. These deposits can make your engine run hot by restricting water flow through the cooling jackets. Calcium buildup also may damage your engine’s water pump. Descaling Engine Flush WILL NOT damage seals, gaskets or rubber impellers.

Features

  • Removes scale and deposits from all marine engines
  • Will not damage engine seals, gaskets or rubber impellers.

Directions

With Starbrite Do It Yourself Marine Engine Descaling Kit #35001

  1. Starbrites Marine Engine Descaling Kit comes with a 5 gallon tank, gate valve/cap and clear hose. You will need ear muffs or flushing attachment for your type of engine and a garden hose.
  2. Check marine engine manual for specific coolant capacity and plan accordingly. Mix one part of concentrated Star brite® Descaling Engine Flush with one part fresh water in the 5 gallon tank, making sure vent cap is open. Once 5 gallon tank is filled with mixture, tighten gate valve/cap and lay tank on side with gate valve facing down.
  3.  Using marine engine flushing attachment (not included in kit) and garden hose, start engine and allow it to reach normal operating temperature to ensure that the thermostat is open to allow Descaling Engine Flush to circulate throughout entire cooling system.
  4. When engine reaches normal operating temperature and thermostat opens, turn off engine and disconnect garden hose from flushing attachment. Attach one end of clear hose to engine flushing attachment and open gate valve to allow Engine Descaling Flush to flow into clear hose.
  5. Start engine and leave run at idle speed until the green mixture comes out of the exhaust/water outlet of your engine. Immediately shut off the engine and close gate valve on tank. Let engine sit for 5-10 minutes.
  6. Open gate valve and turn engine on to allow more flushing mixture to flow through system. After 1-2 minutes, close gate valve and shut engine off. Disconnect clear hose from flushing attachment and connect garden hose. Turn on water supply and start engine. Run engine at idle for 5 minutes, allowing fresh water to run throughout system.
  7. Turn off engine and remove flushing attachment. Rinse down outside of engine. Dispose of flushing mixture in compliance with local, state and federal laws.

Without Starbrite Do It Yourself Marine Engine Descaling Kit

  1. Remove boat from water. Place the motor in an appropriate container so that the engine intake is well below the lip of the container. Mix one part of concentrated Star brite Descaling Engine Flush with one part fresh water. Fill container until engine intake is completely submerged in the Descaling Engine Flush mixture.
  2. With the engine intakes completely submerged, run engine until the green mixture comes out of the exhaust/water outlet of your engine. Immediately shut off the engine and let engine sit for 5-10 minutes. Turn engine on to allow fresh mixture to flow through system, then shut off engine again. Drain entire system
  3. Dispose of flush mixture in compliance with local, state and federal laws. Fill container with fresh water and completely submerge engine intakes in water. Start engine once more and run for 5 minutes while fresh water runs throughout the engine system.
 

Hazard Warnings

Hazard pictogram (GHS-US):
Signal word (GHS-US): Danger
Hazard statement (GHS-US):

H290 - May be corrosive to metals
H315 - Causes skin irritation
H317 - May cause an allergic skin reaction
H318 - Causes serious eye damage
H332 - Harmful if inhaled

Precautionary statement (GHS-US): P234 - Keep only in original container
P261 - Avoid breathing gas
P264 - Wash hands, forearms, and exposed areas thoroughly after handling
P271 - Use only outdoors or in a well-ventilated area
P272 - Contaminated work clothing must not be allowed out of the workplace
P280 - Wear eye protection, protective gloves, protective clothing
P302+P352 - If on skin: Wash with plenty of water
P304+P340 - IF INHALED: Remove person to fresh air and keep at rest in a position comfortable for breathing
P305+P351+P338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
P310 - Immediately call a poison center
P333+P313 - If skin irritation or rash occurs: Get medical advice/attention
P362+P364 - Take off contaminated clothing and wash it before reuse
P390 - Absorb spillage to prevent material damage

Technical Files

Ireland  Safety Data Sheet pdf

Ireland  Safety Data Sheet pdf

View AllClose